Optical Remote Controller |
 |
BRS |
|
 |
MORE COMPACT SIZE AND THINNER THAN USUAL MODEL! EASY TO SEE WITH BACK-LIGHT! Compact, thin body and pocket size |
|
Remote control of OHT |
Notice of loading completion/transmission of destination |
|
It can make a manual operation when testing or system troubled. |
It can instruct load completion or destination from driver on automated warehouse. |
|
|
|
|
|
|
|
Pallet No. instruction on automatic parking |
Shutter opening/closing |
|
It can instruct the specified pallet from the car. |
It can make a remote control for several doors such as shutter etc. at garage or factory. |
 |
 |
Specifications
Specifications(Transmitter)
|
Model No. |
BRS-G2CT |
||||||||
|
Transmission distance |
10m |
||||||||
|
Power source |
Alkaline cell 4 pcs |
||||||||
|
Battery life |
16 hours under continuous use(when not using back-light) |
||||||||
|
Display |
LCD 3 digits, battery, transmission(with back-light) |
||||||||
|
Key numbers |
Numerical key 1 to 15 points, setting key 3 points(Fc, Mod, Ent), Built-in electronic buzzer) |
||||||||
|
ID No. setting |
Max. 999 kinds(It can be set as your option) |
||||||||
|
Setting functions |
|
||||||||
|
Directional angle |
Full angle 30° |
||||||||
|
Wave length |
870nm |
||||||||
|
Modulating method |
Pulse position modulation(455kHz) |
||||||||
|
Error detection |
Twice coincident system |
||||||||
|
Vibration resistance |
Double amplitude 1.5mm, 10 to 55Hz, each 2 hour in X, Y and Z direction |
||||||||
|
Impact resistance |
490m/s2, each 6 time in X, Y and Z directions |
||||||||
|
Ambient temperature/humidity |
0 to +40 degrees C, 45 to 85%RH |
||||||||
|
Protective structure |
IP64 : key operating face, IP40 : the other |
||||||||
|
Case |
Polycarbonate |
||||||||
|
Weight |
Approx. 110g(including battery) |
Specifications(Receiver)
|
Model No. |
BRS-G2CR |
BRS-H2CR |
|
Direction |
HEAD-ON |
Front-ON |
|
Power source |
24VDC±10% |
|
|
Directional angle |
Full angle 90°for right/left, Full angle 40°for up/down |
|
|
ID No. setting |
999 kinds, turn the adjuster counterclockwise : write-in mode(from transmitter),turn the adjuster clockwise : normal mode |
|
|
Indicators |
Data output(OUT1 to 15) : 15 pcs, strobe output(STB) : 1 pcs, receiving lamp (RCV) : 1 pce, write-in lamp(WRT) : 1 pce, power lamp(POW) : 1 pce |
|
|
Output |
Output only when ID No. from transmitter would coincide with setting No. |
|
|
Output holding time |
100msec or more |
|
|
Receiving system |
Pulse position modulation(455KHz), Twice coincident system |
|
|
Connection |
Cable(connector for the terminal end) |
|
Ambient temperature |
0 to +50 degrees C | |
|
Ambient humidity |
45 to 85%RH |
|
|
Ambient illuminance |
4000lx(fluorescent/mercury lamp) |
|
|
Environment |
No corrosive gas |
|
|
Vibration resistance |
Double amplitude 1.5mm, 10 to 55Hz, each 2 hour in X, Y and Z direction |
|
|
Impact resistance |
490m/s2, each 6 time in X, Y and Z directions |
|
|
Insulation resistance |
10MΩ(500VDC megger) |
|
|
Noise resistance |
Conformity standard : IEC(EN)61000-4-2/-3/-4/-6/-8 |
|
|
Protective structure |
IP64 |
|
|
Case |
Polycarbonate |
|
|
Weight |
Approx. 240g |
|
External dimension
Transmitter
Receiver
Output circuit
NPN open-collector output
30VDC 50mA residual voltage 1.8V or less
Connection
|
|
|
Connector (1)12P
(JST PHR-12) Connector (2)10P (JST PHR-10) Shield |
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Note) Don't use attached connector as relay terminal.
