Sensor for special applications/Textile |
 |
PH-BH1-81 |
Sensors for Textile Industry Built-in amplifier type photoelectric switch(8-beam type) |
||||||||||
|
Close monitoring for sliver breakage This is 8 beams reflection type sensor which was developed for detecting sliver breakage of drawing frame s. As the sliver is checked one by one, it is possible to check accurately. Also, it is to detect stably against up/down or right direction because of enough for detecting characteristic. |
||||||||||
Specifications
Sensor
Kind |
Diffuse-reflection type |
Model No. |
PH-BH1-81 |
Power source |
12 to 24VDC ±10％（Ripple 5% or less） |
Current consumption |
200mA(at 12VDC) |
Light source |
Infra-red LED |
Detecting distance |
20 to 80mm(sliver with φ20mm) |
Output |
NPN open-collector output(allowable load voltage 33V or less, allowable load current 100mA or less, residual voltage 0.5V) |
Response time |
Approx. 500msec |
Indicators |
Light-entering lamp : red LED(Lights up when light-entering) |
Connection |
Cable type(2m long, 0.3mm2) |
Ambient illuminance |
Incandescent lamp : 3,000lx or less |
Ambient temperature/humidity |
竏鈀10 degrees C to ＋50 degrees C, 45 to 85％RH |
Vibration resistance |
Double amplitude 1.5mm, 10 to 33Hz, Each 2 hour in X, Y and Z directions |
Impact resistance |
200m/s2, Each 3 time in X, Y and Z directions |
Protective structure |
IP50(IEC standard) |
Case materials |
Case : steel plate(cover : acrylic PBT) |
Weight |
Approx. 1.4kg |
Control unit
Kinds |
32-beam type |
16-beam type |
Model No. |
EA5-1221 |
EA5-1222 |
Connectable numbers |
4 pcs of PH-BH1-81 |
2 pcs of PH-BH1-81 |
Power source |
AC100 to 110V/AC200 to 220V（±10％, 50/60Hz） |
|
Power consumption |
10VA or less |
5VA or less |
Power for sensor |
DC10 to 15V 1A |
DC10 to 15V 0.5A |
Control output |
1C relay and 1a relay(250VAV 4A cosφ=1) |
|
Connection |
Screw terminal(M3) |
|
Ambient temperature/humidity |
竏鈀10 degrees C to ＋50 degrees C, 45 to 85％RH |
|
Vibration resistance |
Double amplitude 1.5mm, 10 to 33Hz, Each 2 hour in X, Y and Z directions |
|
Impact resistance |
200m/s2, Each 3 time in X, Y and Z directions |
|
Protective structure |
IP40(IEC standard) |
|
Case materials |
Case : steel plate(SPCC) |
|
Weight |
Approx. 1.3 kg |
Approx. 1.1 kg |
External dimension
Sensor(PH-BH1-81)
The pitch of each light beam can be set from 25mm to 40mm.
It can adjust the sensitivity as per each light beam.
PH-BH1-61 for 6-beam type is also available.
Control unit(EA5-1221/EA5-1222)
Connection
EA5-1221
EA5-1222
Operation |
||||||||||||||||
|
When normal sliver |
|||||||||||||||
|
Light-entering lamp on the sensor is lighting up. Sliver breakage lamp is going off. |
|||||||||||||||
|
|
|||||||||||||||
|
||||||||||||||||
|
When sliver breakage |
|||||||||||||||
|
Sensor for sliver breakage become s non-light-entering state and light-entering lamp goes off and sliver breakage lamp lights up. |
|||||||||||||||
|
|
|||||||||||||||
|
Note) Sliver breakage lamp and output is self-holding circuit and is keep this state till reset or cutting power source. |
|||||||||||||||
|
Reset(Releasing holding state) |
|
Breakage lamp and output is released by "Close" between 9 & 13. |
