Archive カテゴリ：Photoelectric Switch

FAQ's Category

Auto Counter

Sensor for Textile Industry

Application

Laser Range Finder

Scanning Range Finder (Data Output Type)

Scanning Range Finder (Area Configuration Type)

Photoelectric Switch

3D LiDAR

Area Configuration Type

Optical Data Transmission Device

Sensor for Iron and Steel Industry

Area Configulation Type

Optical Remote Control Device

Archive カテゴリ：Photoelectric Switch

Should I install the PGL based on the center of its housing or the center of the laser spot?

Has the wiring of the PX1-C changed?

Is there a successor to PHE-L3-115 (projector) and PHF-L3-115 (receiver)?

What kind of command is it for PGL setting and reading?

Is it possible to operate the FBX-25DC with one switch for both light-on with control output 1 and dark-on with control output 2?

How can I use the FBX-25JC in Dark-ON mode?

What Should I do when MBF-36T / R keeps its output "ON" even if there is no actual object?

Please tell me the details of EH8-1301.

How should I set the upper and lower limits of HSA-05?

What are the alternatives for PH-1U8 (amplifier) and S-20G / DT (sensor)?

Please tell me the CE standard of LEX-103A.

Are there any objects that are difficult to detect with the HSA-05?

How long is the life of HSA-05?

What is the replacement for PEX-109A?

What is the standard for the antenna flange of MBF-36T / R?

Why can't I change the DC-JB / JC preset values?

What is the alternative to FC-5NA (PNP)?

Please tell me about the bending radius of EH8-1301.

What is the alternative to PEX-263C?

What is a replacement for PLX-305?

Is there a PNP type for FG-31C?

Are there any countermeasures in case of interference between PGL and BWF-2C?

What is the alternative to PX1-2FCW?

What is the indicator light when adjusting the optical axis of the LX2-257AG?

Is there a laser off command for PGL?

What is the difference between PD-10M2Z and PD-10M?

Does PA-SC2 need to be grounded?

What should I do with the terminal processing of EP1-3101?

Is there a successor model to PR-100C and SAC-112?

Do you produce PK7-CR?

What is the allowable load resistance of HSA-05?

What is the difference between LFG-51C-03 and FG-51C?

Is it possible to purchase the PEY reflector separately?

When replacing DM-WD5, is there any problem with BWF-11A / B and serial-parallel converter?

Is the PGL application software compatible with Windows XP?

What error does 290 mean in PGL?

Which of the DMS (NPN type) inputs (IN1 to IN4), mode, and select should be connected to +/-?

Is it possible to use the reflective sheet of PDL-120P with PGL-180W3?

Is it possible to extend the cable of LX1-407C?

As a characteristic of LX2-257AG, is there a characteristic that the variation of distance appears on the + side (long distance side)? When the distance is 1500 mm or more, the variation on the + side will occur, and when the distance is 1500 mm or less, the variation occurs on the - side.

Please tell me the wiring when using only the upper and lower limit alarms of HSA.

PGL is connected to PLC. I wrote a command for measuring data, but I could get the data only once. How can I get the data continuously?

Are DM-DSP and ISP communication compatible?

Is it possible to extend the cable between the sensor head of the LDA-DC and the amplifier unit?

Please tell me the setting method. Does it need calibration input etc.?

What is the precautions when replacing PDL with PGL?

Is there a replacement for PX1?

What is the response time for HSA detection?

When connecting the shield of PGL, where should I connect it to?

Is there any successor model of PL1-30E and PL1-30FA?

The position of the dolly becomes in error and it is happened to collide. It often happens when turning on the power, and after some time the problem is solved. Is there any countermeasures?

It says that the detection range is about 1.5m away, does it mean that the detection range is within 1.5m?

The ambient illuminance is 2 lux, but is it possible to detect flames in the dark?

Is PGL affected by magnetic fields?

I connected to the alarm output, but the alarm is not output even if I approach it.

Will mutual interference occur if multiple devices are used side by side in parallel?

Does the PG-200PA contain PCB?

I want to put a cover on PD-10M, but is there any part that should not be hidden?

What is the laser beam class of PD-10M? How do you set the output

Please tell me the precautions when using PD5 for outdoors.

Is there any problem if we use a retroreflective type reflector that is commercially available when using PEX?

What is the distance LEX can see in an outdoor environment with sunlight?

Are there any objects that are difficult to detect with sensor?

As a characteristic of LX2-257AG, is there a characteristic that the variation of distance appears on the + side (long distance side)?
When the distance is 1500 mm or more, the variation on the + side will occur, and when the distance is 1500 mm or less, the variation occurs on the - side.

PGL is connected to PLC.
I wrote a command for measuring data, but I could get the data only once.
How can I get the data continuously?

Please tell me the setting method.
Does it need calibration input etc.?

What is the laser beam class of PD-10M?
How do you set the output