Archive タグ：UAM

FAQ's Category

Sensor for Iron and Steel Industry

Area Configulation Type

Optical Remote Control Device

Auto Counter

Sensor for Textile Industry

Application

Laser Range Finder

Scanning Range Finder (Data Output Type)

Scanning Range Finder (Area Configuration Type)

Photoelectric Switch

3D LiDAR

Area Configuration Type

Optical Data Transmission Device

Archive タグ：UAM

I am using UAM in ROS, but if I change the model to UST or URM, is it possible to substitute the software as it is?

What is the area input delay of UAM-05LP-T301?

Does the range sensor also support Linux?

How can I switch the area of UAM-05LP-T301?

Do the UAM-05LP-T301 brackets come with the screws?

About blocking when downloading application software

Why is the spread of the light beam different from the front and the side of the LiDAR?

Is there anything I can do if I don't know the IP address of the range sensor?

Is it possible to use the range sensor with Windows pro?

Is there any countermeasure for UAM false detection?

What happens to the slave side when an area switching signal is input to the slave side while using the master-slave function of UAM-05LP-T301?

What are the specifications of UAM's Ethernet cable?

Does the range sensor (PBS / UST / UAM) use OSSD?

When was the time stamp acquired?

When I try to connect to the sensor from Linux, I should be accessing the correct serial port, but I can't.

Is it possible to acquire data from multiple sensors at the same time?

What is the UAM additional safety distance?

What is UAM's additional safety distance?

If a highly reflective background is used as the measured target, should I offset the measured value uniformly by "200 mm"? Or does the distance differ depending on the type of high-reflective object?

I got a UAM error number 89. The error number was not mentioned in the instruction manual. What kind of error is it?

I get a UAM error number 85. What should I do?

How much is the light beam of UAM?

I get an optical window / short-distance error when using the muting function. Is it normal that short-distance error occurs if there is an object near the sensor even in muting mode? The cause is probably smoke. Smoke will be a trigger of the short-distance error.

Is it possible to transfer the data of UAM-02LP to UAM-05LP?

Do I have to connect all the wires when extending the UAM cable?

Is there an output to notify the PLC side when there is an abnormality in UAM?

ー

Please tell us the UL File No and product category. Also, is the optional "UAM-5C02C" UL certified?

What kind of output is synchronous output?

Do you need a exclusive driver for Ethernet type?

The optical window has become dirty. Please tell me how to clean it.

Is it possible to use a USB conversion cable when setting the area?

When using the master-slave function of UAM-05LP-T301, what happens on the slave side when an area switching signal is input to the slave side?

How much can the cable be bent?

A white connector is attached at the time of delivery. Is this for making connection?

What is response time?

What is OOSD output?

Is it possible to change the output to NPN output?

Is it possible to use it without setting a protection area?

I created an area and wrote to the sensor, but why is it output even though there is no object in the area?

What happens if On-delay / Off-delay is set?

Please tell me how to set the hysteresis.

Is it possible to install the sensor upside down?

When setting with the muting function, it is necessary to set a time difference but it is not possible to set them at the same time. How much time difference should be set not to be simultaneously?

Does it work even if power is supplied from the battery?

What is contamination detection?

I'm having trouble with reset input.

Where can I find the error number?

Are there any precautions to take when attaching a cover?

Is there any way to deliberately put the sensor in a malfunction state?

Sensor erroneously detect that there is an obstacle even though there is no object. Why it happens?

Please tell me about the output logic of the Scanning Range Finder.

How many millimeters does a short-distance error occur at?

Please tell me how to use the app.

Sensors Interfere with each other. Please tell me the measures.

I want to connect to a PC and edit the area with the application, but the sensor is not recognized. What should i do?

The light from the sensor is affecting other devices. Is there any measures?

I got a UAM error number 89. The error number was not mentioned in the instruction manual.
What kind of error is it?

I get an optical window / short-distance error when using the muting function. Is it normal that short-distance error occurs if there is an object near the sensor even in muting mode?
The cause is probably smoke. Smoke will be a trigger of the short-distance error.

Please tell us the UL File No and product category.
Also, is the optional "UAM-5C02C" UL certified?

When setting with the muting function, it is necessary to set a time difference but it is not possible to set them at the same time.
How much time difference should be set not to be simultaneously?

I want to connect to a PC and edit the area with the application, but the sensor is not recognized.
What should i do?