Archive タグ：UST

FAQ's Category

Photoelectric Switch

3D LiDAR

Area Configuration Type

Optical Data Transmission Device

Sensor for Iron and Steel Industry

Area Configulation Type

Optical Remote Control Device

Auto Counter

Sensor for Textile Industry

Application

Laser Range Finder

Scanning Range Finder (Data Output Type)

Scanning Range Finder (Area Configuration Type)

Archive タグ：UST

I am using UAM in ROS, but if I change the model to UST or URM, is it possible to substitute the software as it is?

Does the range sensor also support Linux?

How many UST-10LXs can be connected at the same time?

Is there any software to transfer area data from PBS-03JN to UST-05LN?

About blocking when downloading application software

Why is the spread of the light beam different from the front and the side of the LiDAR?

Is it okay to install and use UST-10LX at a height 70 mm from the floor?

What is the maximum voltage and current for the output of the UST-05LN?

Is it possible to use only one output of UST-05LN?

UST-05LN causes chattering. Is there any countermeasure?

Is there anything I can do if I don't know the IP address of the range sensor?

The intensity value of UST-30LX becomes low when the distance is short. Why?

Is it possible to use the range sensor with Windows pro?

Does the UST-30LC have an enclave area function?

What should I do for the UST-20LX to communicate with my computer?

Is it possible to overwrite the data of the old UST-05LN to a new UST-05LN?

When the UST-05LN is started. the inrush current is 400mA. How long does the inrush current flow?

Does the laser beam of UST-05LN decrease due to deterioration over time?

When using with multi-echo function, how much rainfall can be detected with UST-30LX?

Does the range sensor (PBS / UST / UAM) use OSSD?

The UST-30LX has multi-echo support and stain resistance, but what about water droplet adhesion?

Will water droplets on the surface of the UST-10LX optical window affect data acquisition?

I'm running UST using a battery. The battery voltage became low and the UST failed output. How low is the voltage / current before the failure output is triggered? Do you know the exact value?

When was the time stamp acquired?

When I try to connect to the sensor from Linux, I should be accessing the correct serial port, but I can't.

Is it possible to acquire data from multiple sensors at the same time?

How much communication data does the sensor have?

When I run an application that uses the URG library on a PC with low specifications, a communication error sometimes occurs.

Please tell me the accuracy of the time stamp of the sensor (UST-10 / 20LX).

When I install the USB driver and connect the sensor, the mouse cursor moves randomly and clicks on various places.

Even if I set the area of UST-30LC and write it, it is not reflected even if I check it in monitor mode. Why?

Since the UST-30LX is a 30m type, I think that the light will be more spread. Is there any countermeasure?

Please tell me about the difference in UST series detection distance.

Is there a difference in output between the UST-20LX and UST-30LX at short distances (1m to 10m) and medium distances (10m to 20m)?

Area 1 and 2 have the same configuration. Output 1-4 become ON with area1, is the ON-state continue if I change the area from 1 to 2 at this timing.

Please tell me about the output residual voltage of URM and UST.

What is the leakage current of URM and UST?

What kind of output is synchronous output?

Do you need a exclusive driver for Ethernet type?

I connected to a PC, but it does not recognize the sensor. What should I do.

The optical window has become dirty. Please tell me how to clean it.

Is it possible to use a USB conversion cable when setting the area?

How much can the cable be bent?

A white connector is attached at the time of delivery. Is this for making connection?

What is response time?

I created an area and wrote to the sensor, but why is it output even though there is no object in the area?

What happens if On-delay / Off-delay is set?

Please tell me how to set the hysteresis.

Please tell me how to connect to the output.

Is it compatible with Windows 10?

Is it possible to install the sensor upside down?

How wide is the light beam?

Does it work even if power is supplied from the battery?

What is contamination detection?

Are there any precautions to take when attaching a cover?

Is there any way to deliberately put the sensor in a malfunction state?

Sensor erroneously detect that there is an obstacle even though there is no object. Why it happens?

Please tell me about the output logic of the Scanning Range Finder.

Please tell me how to use the app.

How many meters can the cable be extended?

Sensors Interfere with each other. Please tell me the measures.

I want to connect to a PC and edit the area with the application, but the sensor is not recognized. What should i do?

The light from the sensor is affecting other devices. Is there any measures?

I'm running UST using a battery.
The battery voltage became low and the UST failed output.
How low is the voltage / current before the failure output is triggered?
Do you know the exact value?

I want to connect to a PC and edit the area with the application, but the sensor is not recognized.
What should i do?