Archive カテゴリ：Scanning Range Finder (Data Output Type)

FAQ's Category

Auto Counter

Sensor for Textile Industry

Application

Laser Range Finder

Scanning Range Finder (Data Output Type)

Scanning Range Finder (Area Configuration Type)

Photoelectric Switch

3D LiDAR

Area Configuration Type

Optical Data Transmission Device

Sensor for Iron and Steel Industry

Area Configulation Type

Optical Remote Control Device

Archive カテゴリ：Scanning Range Finder (Data Output Type)

Is it possible to use the own program with UTM-30LX-EW, which is created with UTM-30LX?

What is the scratch resistance of UTM-30LX-EW before and after hard coating?

I am using UAM in ROS, but if I change the model to UST or URM, is it possible to substitute the software as it is?

What is the software called the function setting tool of UXM-30LXH-EHA for?

Does the range sensor also support Linux?

How many UST-10LXs can be connected at the same time?

Why is the spread of the light beam different from the front and the side of the LiDAR?

Is it okay to install and use UST-10LX at a height 70 mm from the floor?

Is there anything I can do if I don't know the IP address of the range sensor?

The intensity value of UST-30LX becomes low when the distance is short. Why?

Is it possible to use the range sensor with Windows pro?

Is it possible to overwrite the data of the old UST-05LN to a new UST-05LN?

The instruction manual says that the USB cable of URG-04LX-UG01 should be USB2.0, but how about USB3.0?

Is there any data on the detection angle of UTM-30LX?

What is the difference between the vibration and shock resistance of UTM-30LX and the vibration and shock resistance of the quality reference value?

How much is DMS-HB1-Z01 weight?

When using with multi-echo function, how much rainfall can be detected with UST-30LX?

Does the range sensor (PBS / UST / UAM) use OSSD?

Will water droplets on the surface of the UST-10LX optical window affect data acquisition?

I'm running UST using a battery. The battery voltage became low and the UST failed output. How low is the voltage / current before the failure output is triggered? Do you know the exact value?

When was the time stamp acquired?

When I try to connect to the sensor from Linux, I should be accessing the correct serial port, but I can't.

Is it possible to acquire data from multiple sensors at the same time?

How much communication data does the sensor have?

When I run an application that uses the URG library on a PC with low specifications, a communication error sometimes occurs.

Please tell me the accuracy of the time stamp of the sensor (UST-10 / 20LX).

When I install the USB driver and connect the sensor, the mouse cursor moves randomly and clicks on various places.

The scan cycle of UTM-30LX-EW should be 25ms, but sometimes it becomes 50ms.

URG driver cannot be installed on Windows Embedded Standard 7

Even if I set the area of UST-30LC and write it, it is not reflected even if I check it in monitor mode. Why?

Since the UST-30LX is a 30m type, I think that the light will be more spread. Is there any countermeasure?

What is UAM's additional safety distance?

How much is the weight of the rear mounting bracket and cover bracket of the UGM?

Please tell us about the appearance (material, surface treatment, paint specifications, paint color) of the back mounting bracket and cover bracket of UGM.

Is there a difference in output between the UST-20LX and UST-30LX at short distances (1m to 10m) and medium distances (10m to 20m)?

What is the leakage current of URM and UST?

Is it possible to set 2 points on the same step when setting the area?

Please tell us the UL File No and product category. Also, is the optional "UAM-5C02C" UL certified?

When using URG-04LX-UG01, it is necessary to prepare a USB cable separately, can I use other cables other than Hokuyo's original URG-C001?

What happens if the light is blocked?

Do you need a exclusive driver for Ethernet type?

The optical window has become dirty. Please tell me how to clean it.

What are the start-up conditions for the heater?

Is it possible to use a USB conversion cable when setting the area?

Does the sensor run on USB bus power?

Why is air in the waveguide between the amplifier and antenna of MBX-301A?

How much can the cable be bent?

A white connector is attached at the time of delivery. Is this for making connection?

What is response time?

I created an area and wrote to the sensor, but why is it output even though there is no object in the area?

What happens if On-delay / Off-delay is set?

Please tell me how to connect to the output.

Is it compatible with Windows 10?

Is it possible to install the sensor upside down?

Does it work even if power is supplied from the battery?

What is contamination detection?

What is the conductor size of the cable?

Are there any precautions to take when attaching a cover?

Sensor erroneously detect that there is an obstacle even though there is no object. Why it happens?

Sensors Interfere with each other. Please tell me the measures.

I want to connect to a PC and edit the area with the application, but the sensor is not recognized. What should i do?

The light from the sensor is affecting other devices. Is there any measures?

I'm running UST using a battery.
The battery voltage became low and the UST failed output.
How low is the voltage / current before the failure output is triggered?
Do you know the exact value?

Please tell us the UL File No and product category.
Also, is the optional "UAM-5C02C" UL certified?

I want to connect to a PC and edit the area with the application, but the sensor is not recognized.
What should i do?